logo

Shanghai Clirik Machinery Co.,Ltd



dhl
dhr
Mineral Mill
The current position:Home > Products > Mineral Mill >

Feldspar medium speed mill

Feldspar medium speed mill

Feldspar is a common raw material used in glassmaking, ceramics, and to some extent as a filler and extender in paint, plastics, and rubber. In glassmaking, alumina from feldspar improves product hardness, durability, and resistance to chemical corrosion. In ceramics, the alkalis in feldspar (calcium oxide, potassium oxide, and sodium oxide) act as a flux, lowering the melting temperature of a mixture. Fluxes melt at an early stage in the firing process, forming a glassy matrix that bonds the other components of the system together. In the US, about 66% of feldspar is consumed in glassmaking, including glass containers and glass fiber. Pottery (including electrical insulators, sanitaryware, tableware, and tile) and other uses, such as fillers, accounted for the remainder.

Feldspar medium speed mill:
1) High capacity
2) Low consumption
3) Finished fineness adjustable

Detailed Product Description about Feldspar medium speed mill
Feldspar medium speed mill is mainly applied to grind non-inflammable, non-explosive and brittle materials with Mohs’ hardness under six. Such as calcite, chalk, limestone, dolomite, kaolin, gypsum, and talc etc, totally more than 100 kinds of materials. Product fineness can be controlled between 300~3000 mesh (47~5 micron) 
Comparable with ball mill, Feldspar medium speed mill has features of low cost, high capacity, easy operation; Comparable with Raymond mill for coarse powder up to 325 meshes, it can produce fine powders between 47 and 5 microns (300 to 3000 meshes)

Performance and features of Feldspar medium speed mill
1. High efficiency
Under the same final size and power, the product capacity of micro powder medium speed mill is twice than jet mill and agitation mill.
2. Long lifetime of wearing parts
The roller and ring are made of special material, which improve the grinding efficiency a lot. For same material and final size, the lifetime of its wearing parts can reach to more than one year, about 2-5 times as long as that of vertical shaft impact crusher and turbo-mill. Especially when handling calcium carbonate and calcite, the lifetime can reach 2-5 years.
3. High safety and reliability
There are no rolling bearings and bolts in grinding cavity, so problems caused by bolts shedding or wear of bearings and seal components will never happen.
4. High fineness of products
The product fineness can reach D97≤5μm.
5. Environment friendly
The application of DMC-120 pulse dust collector and muffler reduce the pollution and noise of the dust, which has reached national environment protection standard

Production Line Configuration of Feldspar medium speed mill
The whole set HGM Feldspar medium speed mill consists of  hammer crusher, bucket elevator, storage hopper, vibrating feeder, main unit, inverter classifier, cyclone collector, pulse deduster system, high pressure positive blower, air compressors and electrical control systems

Working Principle of Feldspar medium speed mill
The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.

Technical Data of Feldspar medium speed mill
Model HGM80 HGM90 HGM100 HGM100A HGM125
Ring Diameter(mm) 800 930 1035 1300
Ring Number(PCS) 3 3~4 3 4 4
Roller Number(PCS) 21 24~32 27 34~36 40~44
Main Shaft Speed(r.p.m.) 230~240 200~220 180~200 135~155
Input Size(mm) ≦20
Finished Size/um(mesh) 5-47(325~2500)
Capacity (t/h) 0.5-4.5 0.6-6.5 0.7-7 1-8.5 1.5-12
Outlet Size (L*W*H, m) 13.9*4*6.2 14.7*4.8*7.2 18*4.6*8.6 14*9*10.25
Motor Power(KW) 145-165 185-204 263 263-290 380-430
Note: This specification is just referencing, any changes are subject to the products.
 
Should you have any questions, please do not hesitate to contact us:
Contact person: Cherry. Zhao
Tel: 0086-21-20236178
E-mail: clirik_grinder@163.com; clirik@grinding-mill.in
Address: No.19 Fuqing Road, Pudong New Area, Shanghai 201201, China.
Homepage: http://www.mill-machine.net
Online Message

Message

Name:
E-mail:
tel:
Message:
Product Center
Hot News
Contact US
Address:No.19Fuqing Rd,Shanghai
Tel:0086-21- 58975587
0086-21- 20236178
Fax: 0086-21- 58974855
Postcode: 201201
E-mail:sales@clirik.comcontact